Skip to Main Content
STAAD.Pro Ideas Portal

Welcome to the STAAD.Pro Ideas portal. The purpose of this site is to post ideas for enhancements and new features. We value your feedback and our team regularly reviews your suggestions for consideration in future releases.

You have 3 options for providing feedback:

  1. Vote for an existing Idea. The popularity of an Idea helps us understand its importance to our users.

  2. Comment on an existing Idea. We want to hear your unique point of view.

  3. Add a new Idea. If no existing Idea describes what you would like, add a new one!

When you Vote, Comment, or Add an idea you will also be subscribed to that Idea and will receive status updates. Please note that we may merge or rename Ideas for clarity. Thank you for your support and feedback, it is always appreciated!

ADD A NEW IDEA

All ideas

Showing 438 of 438

Wind Loading on Tapered Sections

Dear Colleagues, // STAAD.Pro CONNECT Edition - Version 22.12.00.142 // there was a situation where we had to find out the lateral forces due to wind on a light pole (tapered profile) and provide suitable support for the same. Wind was applied usi...
Dani Paul over 2 years ago in  1 Future consideration

Make Staad Multi Processor (Multi-Threaded)

This would cut down the analysis time required by STAAD significantly. If it is too much work to change the solver code to benefit from multi-threads, can at least each basic load or each load combination be run at a different thread? There's no r...
Rafael Salgado almost 3 years ago in  1 Future consideration

Auto wind load generation for roof/purlins..

Frequently used for design of all steel structure with shed/roof CONCERN CODE(ALL) especially IS 875 part 3: 1-Sir, staad CE has support the auto wind load as for clad/unclad buildings, this wind load is applied on the surfaces/periphery of buildi...
Sahil Shaikh almost 3 years ago in  4 Future consideration

Calculate section properties when adding new shape to database

Two things here:Have the ability for STAAD (in the physical modeler) to calculate the section properties when entering a new shape into an existing database. For example, I'm adding a new hat channel into the AISI cold formed Profiles database. In...
Ryan Freund almost 3 years ago in  4 Future consideration

Add ability to show "Color by Section" under Properties Tab

Under Properties in Analytical Modeling, one can currently only highlight assigned geometry for a single section at a time. A button could be added to the table that allows you to show all section properties in the current view by color, and then ...
Marcos Luna almost 2 years ago in  4 Already exists

Staad Pro does not include Seismic load NBCC 2015

Dear All, I highly recommend to include calculation of seismic load using NBCC 2015. I see it as a big gap in Staad Pro not to include Seismic loading using NBCC 2015 Thanks a lot
Guest over 4 years ago in  1 Future consideration

Particular Cases for Validation and Calculation of Ly and Lz Lengths in STAAD.Pro

We have noticed that, under certain configurations, the “Effective Length Calculator” tool in STAAD.Pro may yield results that are not conservative, which poses a risk to the structural safety of the project. Allowing users to validate and manuall...
ANNY VILLEGAS about 1 month ago in  1 Future consideration

STAAD.Pro AISC/CSA Code Checks - Eccentric Axial Specification

There is currently no way, other than directly adding rigid body members with the necessary releases, to simulate an an axial angle or tee member (brace) under eccentric axial load. This causes a high amount of manual calculations to determine the...
Guest 4 months ago in  4 Needs review

Add ability to show "Colour by Utilization Ratio" for 3D view in post processing workflow

It would be good to have a 3D view in post processing with colours of the beam as defined with a UR value. It is possible to have this with beam view now, but would be good if we have it for 3D view like SACS have. (as shown below for example).
Guest 11 months ago in  2 Needs review

Steel AutoDrafter Implementation Required

Dear Sir / Madam, Steel Auto Drafter is not giving beam presentation as per Releases provide in Analytical Modelling. Please check attached screenshot for your ready reference. Steel AutoDrafter drawings should be as per Release and Analytical mod...
Keyur Patel almost 2 years ago in  7 Future consideration