Skip to Main Content
STAAD.Pro Ideas Portal

Welcome to the STAAD.Pro Ideas portal. The purpose of this site is to post ideas for enhancements and new features. We value your feedback and our team regularly reviews your suggestions for consideration in future releases.

You have 3 options for providing feedback:

  1. Vote for an existing Idea. The popularity of an Idea helps us understand its importance to our users.

  2. Comment on an existing Idea. We want to hear your unique point of view.

  3. Add a new Idea. If no existing Idea describes what you would like, add a new one!

When you Vote, Comment, or Add an idea you will also be subscribed to that Idea and will receive status updates. Please note that we may merge or rename Ideas for clarity. Thank you for your support and feedback, it is always appreciated!

ADD A NEW IDEA

FILTER BY CATEGORY

All ideas

Showing 171 of 171

Add New Zealand concrete design (NZS 3101) to Staad Pro

These could be used when performing member or shell design in STAAD.Pro, as well as Advanced Concrete design. See applicable snapshots attached. User would like to be able to do design to NZ codes in STAAD.Pro (specifically concrete and timber,...
Guest 2 months ago in  2 Planned

activate ALT+V+V Short Cut Key again in Connect version of STAAD.

This is very usefull in viewing, selecting to view, viewing whole structure without zooming out etc. This will make STAAD pro operation faster.
Guest 5 months ago in  1 Already exists

Steel design result from multiple design blocks

Currently, if there are multiple design blocks present in a STAAD model, in the post-processing utilization table, design ratio from the last design block is reported. It is very common to define multiple design blocks with different set of parame...
Surojit Ghosh 5 months ago in  1 Future consideration

RCDC not reading beams over slab tank

dear teams,please make corrects for software when you design water tank with slab including beams,RCDC not reading beams,plz correct it,thanks in advance
barham ibrahim 3 months ago in  1 Will not implement

Physical Modeler - Allow multiple wind load definitions to be combined into one primary load case

Because you must create multiple wind definitions for wind along a single direction (i.e. windward, leeward, sidewall) it would be helpful to have the ability to combine these in a single load case. Combining them in the load combos is cumbersome....
R Freund 5 months ago in  1 Future consideration

Automate the option of dynamic wave pressure

There is a webinar for modelling, analysis and design of rcc rectangular water retaining structure along with impulsive and convective wave pressure on coffee corner, but there are some limitations and assumptions, like the xml templates are only ...
Guest 5 months ago in  4 Will not implement

Multiple mass models/ seismic analyses for design

Many codes, particularly IS 1893 part-2 and IS 3370 part-2, the RCC elevated/underground water retaining structure should be analyse and design in "TANK ENPTY" and "TANK FULL" both of the conditions, but staad pro seismic definition whether it is ...
Guest 5 months ago in  2 Planned

Structure discontinuties not allowed for dynamic analysis

Structure discontinuties provided for thermal expansion isn't allowed in dynamic analysis, so provide feature so that we can analyse such structure without separating the model in individual file..
Guest 5 months ago in  2 Already exists

Add a command to modify tension Flange net area for AISC 360 F13

There is the command NSF that modifies the net area of the whole member, but there isn't a command to modify the net area of the tension flange only to apply it to section F13 in AISC.
Dallin Strong 5 months ago in  2 Planned

Steel Design Parameters in Modeller

I assume this has been mentioned before (might even be working on it), but being able to specify the steel design parameters in the Modeler would be a game changer. A separate design module would be good too, but I don't think it's necessary.
R Freund about 1 year ago in  1 Planned